_programming-halogen-to-mute-all-outputs-using-a-fire-alarm-contact-closure-input.jpg "Programming Halogen to mute all outputs using a fire alarm contact closure input from toggle logic Video Screenshot Preview")
GalleryPlay Video:
(Note: The default playback of the video is HD VERSION. If your browser is buffering the video slowly, please play the REGULAR MP4 VERSION or Open The Video below for better experience. Thank you!)
⏲ Duration: 6 min 68 sec
✓ Published: 23-Sep-2014
✓ Published: 23-Sep-2014
Description:
This video shows two ways to program Halogen to mute all the outputs from a contact closure input wired to a HAL Logic input port. n1) One way is to create a single Link that contains all the output Mute (toggle) controls plus the logic input toggle.n2) Or create a Toggle Preset and store all the output blocks in a muted state to this Preset. Then link the Logic input to the Toggle Preset.nA brief introduction to Presets and use of the Baseline Preset is discussed at the end.nA third way to mute
This video shows two ways to program Halogen to mute all the outputs from a contact closure input wired to a HAL Logic input port. n1) One way is to create a single Link that contains all the output Mute (toggle) controls plus the logic input toggle.n2) Or create a Toggle Preset and store all the output blocks in a muted state to this Preset. Then link the Logic input to the Toggle Preset.nA brief introduction to Presets and use of the Baseline Preset is discussed at the end.nA third way to mute
Share with your friends:
Whatsapp | Viber | Telegram | Line | SMS
Email | Twitter | Reddit | Tumblr | Pinterest
Related Videos
_eevblog-262-world39s-simplest-soft-latching-power-switch-circuit.webp "EEVblog")
_raspberry-pi-plus-sunfounder-2-channel-relay-board.webp "Setup RaspberryPi to control a Sunfounder 2 Channel Relay board. This board isn't optimal for the raspberry pi 'cause of a common ground on both sides of the opto-isolator and being setup for 5V control logic. But if you're not worried about voltage spikes or HF noise between the opto-isolator and the relay, it seems to work fine. 3.3V from the RasPi's GPIO is apparently enough to drive the LED in the opto-isolator.nnI'm not sure i would use this board on a remote device due to the common ground")
_toggle-on-off-with-momentary-switch.webp "learnelectronics")
_classic-circuits-you-should-know-single-button-toggle.webp "learnelectronics")
_allen-bradley-plc-one-button-on-off-logic.webp "IMAT")
_using-toggle-logic-on-a-compactlogix-plc.webp "SCADA Lab")
_apartment-growth-map-digital-anyang-apap-2010.webp "This visualization focuses on the explosion of apart- ments in Anyang over the last 30 years. The primary view shows the geographical growth of apartments over time. The bar graph below the time slider shows the number of households constructed during that year. Filters can be selected from the menu to the left to view the apartments by Construction/Manage- ment Company, Building Typology, Construction Date, Price and Number of Stories. Clicking on the button at the lower left of the screen will")
_relay-one-push-button-on-off-switch-simulation-124-one-pushbutton-on-off-relay-switch-circuit.webp "circuitspedia")
⏲ 38 seconds 👁 41.7K
_eevblog-262-world39s-simplest-soft-latching-power-switch-circuit.jpg)
_raspberry-pi-plus-sunfounder-2-channel-relay-board.jpg)
_toggle-on-off-with-momentary-switch.jpg)
_classic-circuits-you-should-know-single-button-toggle.jpg)
_allen-bradley-plc-one-button-on-off-logic.jpg)
_using-toggle-logic-on-a-compactlogix-plc.jpg)
_apartment-growth-map-digital-anyang-apap-2010.jpg)
_relay-one-push-button-on-off-switch-simulation-124-one-pushbutton-on-off-relay-switch-circuit.jpg)
![[+]](/images/menu.gif){kind=small}